C&M provides a complete range of power, control, signal, and data cables and assemblies. Our bulk cable products are segmented as follows:
Power Cable High Flex Shielded Multi-paired Oil and chemical resistant Composite High buoyancy Potable water cable	Data & Control Cable SCSI, Ultra SCSI, Fibre Channel, Infiniband Telecom High speed coax and Advanced hybrid constructions Oil and chemical resistant Shielded  Composite	Cable Design Profiles Flat cable Podded cable Round cable Shot gun cable Coil Cord
Conductors Data, signal, or power flows through the conductor.
Conductor Materials Copper  Copper clad steel  Alloys Aluminum Tinsel	Strand Constructions Bunch True concentric True equal-lay Unidirectional concentric Unidirectional uni-lay  Rope	Coating Methods Hot dip Electroplating Cladding
Conductor Types Stranded Solid	Conductor Coating Tin Silver Nickel Gold	Coating Types Tinned or heavy tinned Pre-fused  Topcoated  Overcoated
Insulation is the material which is extruded over the conductor. Once the insulation is applied to the conductor it is called the primary wire. The insulation is applied to the conductor with an extruder which melts the insulation, pushes it through a barrel, and into a tip and die through which the conductor passess.
Insulation Material Polyvinyl Chloride (PVC) Semi Rigid PVC Polyethylene (thermoplastic) Polyethylene (foamed, cellualar, cross linked, flame retardant) Polypropylene (thermoplastic)	Polyurethane Hytrel Nylon Surlyn Thermoplastic rubber (TPR) Neoprene (thermoset rubber) Styrene Butadiene Rubber (SBR) (thermoset rubber)	Kynar Solef Teflon PFA Teflon FEP Tefzel ETFE Halar ECTFE
Overmolding  C&M performs overmolding operations to shock proof, water proof, dust proof and ruggedize electronic assemblies and electrical interconnects. Overmolding is also utilized to contour and streamline assemblies and interconnects to meet mechanical design requirements and styling. C&M employs the following processes in molding techniques: Hot melt technology (low pressure injection molding) Thermoplastic molding Insert injection molding Liquid silicone rubber molding
Molding Materials Utilized Liquid Silicone Rubber (LSR) Polyvinyl Chloride (PVC) Semi Rigid PVC Polycarbonate (PC) Polypropylene (PP)	Polyethylene (PE, LDPE, HDPE): Foamed/Celluar (FPE), Flame Retardant (FRPE)   Polyurethane Polyester: Hytrel Nylon (Polyamide) Carbothane	Thermoplastic rubber (TPR) Thermoplastic elastomer (TPE) ABS/PCABS Liquid crystal polymer (LCP) Fluoronated Polymers: Teflon (PFA, FEP), Tefzel (TEFZ), Kynar (PVDF)
Connectors Connector modification Molded connector and mechanical connectors
Coil Cords / Retractile Cables Coil Cord Diameter Coil outer diameters 1/8 inch up to 5 inches Cable Types Any jacketed bulk cable (any jacket material)
Production Equipment 18 Extruders 2 Planetaries (15) 24 Carrier braiders (60) 16 Carrier braiders 13 Cablers 1 Pad printing machine 4 Coil cording machines 7 Reversers (coil cords) 10 Auto coilers 9 Twinners 4 Hi-pot testers 2 Salvage machines	3 Strippers 2 Large tapers 6 Respoolers 15 Small tape machines 1 Artos wire stripper 1 Eubanks 4600 cut machine 13 Amp ferrule crimpers   6 Kersten PP3 crimpers 7 JST AP-K2N crimpers 33 Mod plug presses 71 Schleuniger air strippers 48 Carpenter strippers	1 Laser stripper 24 Spiral shielders 2 AMP Champomator 2.5+ module 12 AMP K-presses 25 AMP Stripper crimpers 13 AMP G-presses 2 Hirose CM-105 crimpers 16 Horizontal insert molding machines 1 Vertical insert molding machine  1 Horizontal molding machine 4 Hot melt machines